WORLDWIDE
Home
/
Product Line
Drip Hose, Drip Tape
An Jarl Enterprise Co., Ltd is proud to offer all of the leading brands in performance drip hose, drip tape, irrigation drip tape, at prices suitable for any budget. Most importantly, we back every one of our products with the best one-on-one customer service you'll find anywhere. For over 35 years, we've offered the trusted drip tape fittings to fit our customer's requirement. Our work is dedicated to the creation of progress with inspiring, innovative solutions and to a trusting partnership towards our customers and partners with common benefits. Thank you for your time and business, if you have any questions or needs, please do not hesitate to contact us.
Categories > Drip Irrigation System, BJ Series, white drip tape, Drippers, emitter, Fittings to assemble a water saving drip irrigation sysytem
White Drip Tape BJ-500W
White drip tape reduce the temperature of water inside the drip tape for drip irrigation
WHITE DRIP TAPE IRRIGATION SYSTEM
White drip tape has 2 plies of wall. Outer ply is white and inner ply is black. This white drip tape is designed to reduce the temperature of water inside the drip tape. Since black is easy to absorb heat, black drip tape is easy to heat the inside water under the sun. Hot water may hurt crops. Especially for the crops that are more sensitive to high temperatures water. For example strawberries irrigation is much need to white drip tapes so that irrigation water can be cooler. In general, after drip irrigation there is some water remaining in drip tape. The remaining water inside drip tape may heated by more than 50∘C. White tape can keep the water temperature low while drip tape is exposure under the sunlight. When the irrigation is restarted, the temperature of the first drop of water will be lower.
Drip Hose is a hose with a special designed patch attached inside the hose at the outlet of the holes. This structure can reduces the pressure from the hose lead to almost no pressure,and then makes the water comes out from hose drip by drip, (instead of spray out by pressure inside the hose.) This design also keeps the flow rate in a uniformity way.
The biggest benefit of drip irrigation is: saving irrigation water. It also gives the crop a uniform amount of irrigation water. The drip tape or pipe is used for this purpose.
There is a water outlet at every certain distance on the drip irrigation tape. The water outlet has a labyrinth structure in the drip tape to control the water flow. In general, each water outlet flow at water output is less than 3 liters per hour.
The water in each water outlet flows out in dots, damps the ground, and then sinks downward and spreads to the surrounding ground. To choose suitable drip spacing of the outlet holes depends on the spacing of the crops and the amount of irrigation water required. The flow rate from a single outlet per hour multiplied by the average number of outlets per meter is the total amount of water flow per meter per hour.
A good drip irrigation tape has a small difference in the amount of water discharged from each outlet. The shorter the spacing of the outlet holes, the shorter of time to water each other between the holes, and the higher the uniformity of irrigation. But the relative amount of water per meter is greater.
In general, the difference in the amount of water discharged from each outlet hole should be controlled under 20%. No matter the hole is at the front or end of the drip tape.
The working water pressure of the irrigation tape is around 1 kg/cm2. The labyrinth of narrow water channel is designed inside the outlet to limit the water flow. Because the labyrinth water channel is narrow and curved, it is easily blocked by dirt. Therefore, drip irrigation must have a clean water source. And in the drip irrigation system at the inlet of the main water pipe, a filtration system must be installed. If the irrigation water source is very clean, only a disc or mesh filter is enough. The purpose is to filter the dirt in the water. The filtration system needs to be cleaned from time to time. Reduce the clogging of the filtration system itself and prevent the dirt from flowing into the drip irrigation tape. Check the pressure difference between the inlet and outlet of the filtration system to estimate the degree of filter blockage. The filter must disassemble and wash sometimes.
The filtration system only slows down the obstruction of the drip irrigation tape. Finally, the drip tape must be replaced if it is blocked by dirt and mineral crystals in the water. It is usually replaced once a year to avoid no drip at some section from the drip irrigation tape.
We have all the supply of ready-made accessories, a variety of joints, allow farmers to easily deploy the entire drip irrigation system.
White drip tape has 2 plies of wall. Outer ply is white and inner ply is black. This white drip tape is designed to reduce the temperature of water inside the drip tape. Since black is easy to absorb heat, black drip tape is easy to heat the inside water under the sun. Hot water may hurt crops. Especially for the crops that are more sensitive to high temperatures water. For example strawberries irrigation is much need to white drip tapes so that irrigation water can be cooler. In general, after drip irrigation there is some water remaining in drip tape. The remaining water inside drip tape may heated by more than 50∘C. White tape can keep the water temperature low while drip tape is exposure under the sunlight. When the irrigation is restarted, the temperature of the first drop of water will be lower.
Drip Hose is a hose with a special designed patch attached inside the hose at the outlet of the holes. This structure can reduces the pressure from the hose lead to almost no pressure,and then makes the water comes out from hose drip by drip, (instead of spray out by pressure inside the hose.) This design also keeps the flow rate in a uniformity way.
The biggest benefit of drip irrigation is: saving irrigation water. It also gives the crop a uniform amount of irrigation water. The drip tape or pipe is used for this purpose.
There is a water outlet at every certain distance on the drip irrigation tape. The water outlet has a labyrinth structure in the drip tape to control the water flow. In general, each water outlet flow at water output is less than 3 liters per hour.
The water in each water outlet flows out in dots, damps the ground, and then sinks downward and spreads to the surrounding ground. To choose suitable drip spacing of the outlet holes depends on the spacing of the crops and the amount of irrigation water required. The flow rate from a single outlet per hour multiplied by the average number of outlets per meter is the total amount of water flow per meter per hour.
A good drip irrigation tape has a small difference in the amount of water discharged from each outlet. The shorter the spacing of the outlet holes, the shorter of time to water each other between the holes, and the higher the uniformity of irrigation. But the relative amount of water per meter is greater.
In general, the difference in the amount of water discharged from each outlet hole should be controlled under 20%. No matter the hole is at the front or end of the drip tape.
The working water pressure of the irrigation tape is around 1 kg/cm2. The labyrinth of narrow water channel is designed inside the outlet to limit the water flow. Because the labyrinth water channel is narrow and curved, it is easily blocked by dirt. Therefore, drip irrigation must have a clean water source. And in the drip irrigation system at the inlet of the main water pipe, a filtration system must be installed. If the irrigation water source is very clean, only a disc or mesh filter is enough. The purpose is to filter the dirt in the water. The filtration system needs to be cleaned from time to time. Reduce the clogging of the filtration system itself and prevent the dirt from flowing into the drip irrigation tape. Check the pressure difference between the inlet and outlet of the filtration system to estimate the degree of filter blockage. The filter must disassemble and wash sometimes.
The filtration system only slows down the obstruction of the drip irrigation tape. Finally, the drip tape must be replaced if it is blocked by dirt and mineral crystals in the water. It is usually replaced once a year to avoid no drip at some section from the drip irrigation tape.
We have all the supply of ready-made accessories, a variety of joints, allow farmers to easily deploy the entire drip irrigation system.
Drip Elbow Nipple BJ-521
16 mm quick elbow nipple for lateral drip tape from top of main tube in drip irrigation system
This quick elbow nipple is both end of 16 mm diameter nipple. One end insert into a rubber ring in the hole drilled on the distribute pipe. The other end can quickly connect drip tape with an active ring. It is convenient to connect, in case of the distribute pipe drilled holes at upper side to be the outlets.
The biggest benefit of drip irrigation is: saving irrigation water. It also gives the crop a uniform amount of irrigation water. The drip tape or pipe is used for this purpose.
There is a water outlet at every certain distance on the drip irrigation tape. The water outlet has a labyrinth structure in the drip tape to control the water flow. In general, each water outlet flow at water output is less than 3 liters per hour.
The water in each water outlet flows out in dots, damps the ground, and then sinks downward and spreads to the surrounding ground. To choose suitable drip spacing of the outlet holes depends on the spacing of the crops and the amount of irrigation water required. The flow rate from a single outlet per hour multiplied by the average number of outlets per meter is the total amount of water flow per meter per hour.
A good drip irrigation tape has a small difference in the amount of water discharged from each outlet. The shorter the spacing of the outlet holes, the shorter of time to water each other between the holes, and the higher the uniformity of irrigation. But the relative amount of water per meter is greater.
In general, the difference in the amount of water discharged from each outlet hole should be controlled under 20%. No matter the hole is at the front or end of the drip tape.
The working water pressure of the irrigation tape is around 1 kg/cm2. The labyrinth of narrow water channel is designed inside the outlet to limit the water flow. Because the labyrinth water channel is narrow and curved, it is easily blocked by dirt. Therefore, drip irrigation must have a clean water source. And in the drip irrigation system at the inlet of the main water pipe, a filtration system must be installed. If the irrigation water source is very clean, only a disc or mesh filter is enough. The purpose is to filter the dirt in the water. The filtration system needs to be cleaned from time to time. Reduce the clogging of the filtration system itself and prevent the dirt from flowing into the drip irrigation tape. Check the pressure difference between the inlet and outlet of the filtration system to estimate the degree of filter blockage. The filter must disassemble and wash sometimes.
The filtration system only slows down the obstruction of the drip irrigation tape. Finally, the drip tape must be replaced if it is blocked by dirt and mineral crystals in the water. It is usually replaced once a year to avoid no drip at some section from the drip irrigation tape.
We have all the supply of ready-made accessories, a variety of joints, allow farmers to easily deploy the entire drip irrigation system.
The biggest benefit of drip irrigation is: saving irrigation water. It also gives the crop a uniform amount of irrigation water. The drip tape or pipe is used for this purpose.
There is a water outlet at every certain distance on the drip irrigation tape. The water outlet has a labyrinth structure in the drip tape to control the water flow. In general, each water outlet flow at water output is less than 3 liters per hour.
The water in each water outlet flows out in dots, damps the ground, and then sinks downward and spreads to the surrounding ground. To choose suitable drip spacing of the outlet holes depends on the spacing of the crops and the amount of irrigation water required. The flow rate from a single outlet per hour multiplied by the average number of outlets per meter is the total amount of water flow per meter per hour.
A good drip irrigation tape has a small difference in the amount of water discharged from each outlet. The shorter the spacing of the outlet holes, the shorter of time to water each other between the holes, and the higher the uniformity of irrigation. But the relative amount of water per meter is greater.
In general, the difference in the amount of water discharged from each outlet hole should be controlled under 20%. No matter the hole is at the front or end of the drip tape.
The working water pressure of the irrigation tape is around 1 kg/cm2. The labyrinth of narrow water channel is designed inside the outlet to limit the water flow. Because the labyrinth water channel is narrow and curved, it is easily blocked by dirt. Therefore, drip irrigation must have a clean water source. And in the drip irrigation system at the inlet of the main water pipe, a filtration system must be installed. If the irrigation water source is very clean, only a disc or mesh filter is enough. The purpose is to filter the dirt in the water. The filtration system needs to be cleaned from time to time. Reduce the clogging of the filtration system itself and prevent the dirt from flowing into the drip irrigation tape. Check the pressure difference between the inlet and outlet of the filtration system to estimate the degree of filter blockage. The filter must disassemble and wash sometimes.
The filtration system only slows down the obstruction of the drip irrigation tape. Finally, the drip tape must be replaced if it is blocked by dirt and mineral crystals in the water. It is usually replaced once a year to avoid no drip at some section from the drip irrigation tape.
We have all the supply of ready-made accessories, a variety of joints, allow farmers to easily deploy the entire drip irrigation system.
Drip Nipple BJ-521M
1/2" Male Thread with 16mm quick L nipple as a lateral drip tape irrigation fitting from top 1/2" female thread of main pipe
This quick L nipple is a connector with one end of 1/2" male thread to connect the main pipe, and the other end of 16 mm to connect drip tape. It is convenient to connect in case the main pipe has a 1/2" female outlet.
WHITE DRIP TAPE IRRIGATION SYSTEM
White drip tape has 2 plies of wall. Outer ply is white and inner ply is black. This white drip tape is designed to reduce the temperature of water inside the drip tape. Since black is easy to absorb heat, black drip tape is easy to heat the inside water under the sun. Hot water may hurt crops. Especially for the crops that are more sensitive to high temperatures water. For example strawberries are much need to white drip tapes so that irrigation water can be cooler. In general, after drip irrigation there is some water remaining in drip tape. The remaining water inside drip tape may heated by more than 50∘C. White tape can keep the water temperature low while drip tape is exposure under the sunlight. When the irrigation is restarted, the temperature of the first drop of water will be lower.
WHITE DRIP TAPE IRRIGATION SYSTEM
White drip tape has 2 plies of wall. Outer ply is white and inner ply is black. This white drip tape is designed to reduce the temperature of water inside the drip tape. Since black is easy to absorb heat, black drip tape is easy to heat the inside water under the sun. Hot water may hurt crops. Especially for the crops that are more sensitive to high temperatures water. For example strawberries are much need to white drip tapes so that irrigation water can be cooler. In general, after drip irrigation there is some water remaining in drip tape. The remaining water inside drip tape may heated by more than 50∘C. White tape can keep the water temperature low while drip tape is exposure under the sunlight. When the irrigation is restarted, the temperature of the first drop of water will be lower.
Drip Nipple BJ-521P
1/2" 16mm quick PVC L nipple to connect drip tape main PVC pipe in 1/2" branch of PVC T fittings
This L nipple is one end of diameter 1/2" with the other end of 16 mm, to connect between main pipe and drip tape. It is made of PVC and convenient to connect the 16 mm drip pipe to main pipe with a 1/2" PVC outlet.
Drip Nipple BJ-522
16 mm quick straight nipple with rubber seal ring for lateral drip tape, a drip tape fitting in a drip irrigation system
This quick straight nipple is both ends of 16 mm diameter nipple. One end insert into a rubber ring in the hole drilled on the distribute pipe. One end connect with drip tape. It is convenient to connect in case of the distribute pipe drilled the holes at side to be the outlets.
The biggest benefit of drip irrigation is: saving irrigation water. It also gives the crop a uniform amount of irrigation water. The drip tape or pipe is used for this purpose.
There is a water outlet at every certain distance on the drip irrigation tape. The water outlet has a labyrinth structure in the drip tape to control the water flow. In general, each water outlet flow at water output is less than 3 liters per hour.
The water in each water outlet flows out in dots, damps the ground, and then sinks downward and spreads to the surrounding ground. To choose suitable drip spacing of the outlet holes depends on the spacing of the crops and the amount of irrigation water required. The flow rate from a single outlet per hour multiplied by the average number of outlets per meter is the total amount of water flow per meter per hour.
A good drip irrigation tape has a small difference in the amount of water discharged from each outlet. The shorter the spacing of the outlet holes, the shorter of time to water each other between the holes, and the higher the uniformity of irrigation. But the relative amount of water per meter is greater.
In general, the difference in the amount of water discharged from each outlet hole should be controlled under 20%. No matter the hole is at the front or end of the drip tape.
The working water pressure of the irrigation tape is around 1 kg/cm2. The labyrinth of narrow water channel is designed inside the outlet to limit the water flow. Because the labyrinth water channel is narrow and curved, it is easily blocked by dirt. Therefore, drip irrigation must have a clean water source. And in the drip irrigation system at the inlet of the main water pipe, a filtration system must be installed. If the irrigation water source is very clean, only a disc or mesh filter is enough. The purpose is to filter the dirt in the water. The filtration system needs to be cleaned from time to time. Reduce the clogging of the filtration system itself and prevent the dirt from flowing into the drip irrigation tape. Check the pressure difference between the inlet and outlet of the filtration system to estimate the degree of filter blockage. The filter must disassemble and wash sometimes.
The filtration system only slows down the obstruction of the drip irrigation tape. Finally, the drip tape must be replaced if it is blocked by dirt and mineral crystals in the water. It is usually replaced once a year to avoid no drip at some section from the drip irrigation tape.
We have all the supply of ready-made accessories, a variety of joints, allow farmers to easily deploy the entire drip irrigation system.
The biggest benefit of drip irrigation is: saving irrigation water. It also gives the crop a uniform amount of irrigation water. The drip tape or pipe is used for this purpose.
There is a water outlet at every certain distance on the drip irrigation tape. The water outlet has a labyrinth structure in the drip tape to control the water flow. In general, each water outlet flow at water output is less than 3 liters per hour.
The water in each water outlet flows out in dots, damps the ground, and then sinks downward and spreads to the surrounding ground. To choose suitable drip spacing of the outlet holes depends on the spacing of the crops and the amount of irrigation water required. The flow rate from a single outlet per hour multiplied by the average number of outlets per meter is the total amount of water flow per meter per hour.
A good drip irrigation tape has a small difference in the amount of water discharged from each outlet. The shorter the spacing of the outlet holes, the shorter of time to water each other between the holes, and the higher the uniformity of irrigation. But the relative amount of water per meter is greater.
In general, the difference in the amount of water discharged from each outlet hole should be controlled under 20%. No matter the hole is at the front or end of the drip tape.
The working water pressure of the irrigation tape is around 1 kg/cm2. The labyrinth of narrow water channel is designed inside the outlet to limit the water flow. Because the labyrinth water channel is narrow and curved, it is easily blocked by dirt. Therefore, drip irrigation must have a clean water source. And in the drip irrigation system at the inlet of the main water pipe, a filtration system must be installed. If the irrigation water source is very clean, only a disc or mesh filter is enough. The purpose is to filter the dirt in the water. The filtration system needs to be cleaned from time to time. Reduce the clogging of the filtration system itself and prevent the dirt from flowing into the drip irrigation tape. Check the pressure difference between the inlet and outlet of the filtration system to estimate the degree of filter blockage. The filter must disassemble and wash sometimes.
The filtration system only slows down the obstruction of the drip irrigation tape. Finally, the drip tape must be replaced if it is blocked by dirt and mineral crystals in the water. It is usually replaced once a year to avoid no drip at some section from the drip irrigation tape.
We have all the supply of ready-made accessories, a variety of joints, allow farmers to easily deploy the entire drip irrigation system.
Drip Nipple BJ-522M
1/2" Male Thread with 16mm quick straight nipple
This straight nipple is one end of 1/2" male thread with another end of diameter 16mm connector to connect drip tape. It is convenient to connect in case the main pipe has a 1/2" female thread outlet.
Drip Nipple BJ-522P
1/2" 16mm PVC straight quick nipple to connect drip tape with PVC T fittings in 1/2" branch
This straight nipple is one end of 1/2" connector with the other end of 16mm diameter connector to connect drip tape. It is made of PVC and convenient to connect, in case the main pipe has a 1/2" PVC outlet.
Drip Stopper BJ-523
16mm straight quick end stopper (plug) for drip tape
This quick straight end stop is diameter 16mm with one ring to assembly at the end of drip tape and quick set with the ring. Its hole of the plug end can be insert a fixer make it steady. Not removed by wind.
Drip Nipple BJ-532
16mm nipple rubber ring to insert hole on main tube to fix BJ-521 quick L nipple or BJ-522 quick straight nipple
Used for quick L nipple or straight nipple. Inlet end of the nipple insert into this rubber ring in the hole drilled on the distribute pipe. The other end connect with drip tape. It is convenient to connect in case of the distribute pipe drilled the holes to be the outlets.
Drip Connector BJ-560R
16mm quick straight connector to connect 2 pieces of drip tape
This quick straight connector is diameter 16mm with 2 rings to assembly at 2 sections of drip tape and quick set with the rings.
Drip Connector BJ-560S
16mm screw straight connector to join 2 sections of drip tape and set with the screws
This screw straight connector is diameter 16mm with 2 ends of screw to join 2 sections of drip tape and set with the screws.
Drip Connector BJ-561
16mm quick L connector to connect 2 sections of drip tape
This quick L connector is diameter 16mm with 2 rings to assembly at 2 sections of drip tape and quick set with the ring. It is convenient for a 90 degree turn of drip tape.
Dripper BJ-571
Quick insert drip emitter (dripper) can be used for different pipe to irrigate, PE pipe, PE flat hose, PVC pipe
This drip emitter has center insert-er makes it easy to insert into PE pipe. Its special screw flow channel structure keeps the drip rate stable and uniform between each emitter. This drip emitter is designed to be clogged-proof , but once even it still clog, it is easy to clean the clog, just use the attached small white pin in the packaging bag to pick out the clog, then it will as clean like a new one . This emitters drip flow fate is 0.48 L/H, it's the most water saving drip emitter ever. Very useful to drip ring for (fruit) tree.
Venturi Injector AJ-251
Venturi Injector for fertilizer or nutrition injection in fertigation system
Venturi injector can absorb liquid fertilizer or nutrition and inject into the irrigation water. It is the important element for fertigation system. This system can feed and control the fertilizer or nutrition automatically when irrigation process begin.
An Jarl Enterprise Co., Ltd is a leading manufacturer and exporter in Taiwan since 1985, specialized in wide range of drip hose, drip tape. Our products enjoy well-reputation by the strict quality request. Customers will be able to check progress and see when they can order by checking their details on the website. We look forward to building on the progress of the roll-out to date and bringing fast irrigation drip tape to as many people as possible, as quickly as possible. If you have any questions, want to buy in bulk, or have us give you a quote for a drip tape fittings to fit your needs, please email to us.